Braided line for spin cast

[Mr. Shannon O'Brien]

You all have probably gone over this a hundred times, but I'd appreciate a response.

I'd like to try a fire line or super braid for tossing size 4 and 5 spinners.

What kind of experiences have some of you had with trying this method?

I'm tired of the memory of mono and hope that a braided line can do on a spin cast.

If this is a winner should I have a tackle store put the line on so it does not sink?

I've never experimented with braided line except fishing over sized halibut in Cook Inlet and sturgeon in the Gorge. And that line was big stuff.

Thanks for your time!

[Sir Fishalot]

Somebody please help this fella out (I don't fish spinners so I've got no advice).

[Sir Fishalot]

O'Brien, check out this link for a little info...
http://www.ifish.net/ubb/ultimatebb....c;f=1;t=032946

[First Bite]

I have used it a little with spoons and spinners. Mainly just tossing some hardware after running drift & bobber stuff thru a hole. It seemed to work fine but a little more work when you snag up. Remember the strength of your rod when you start pulling.

Mark

[salmurai]

I've used Fireline for a couple of years now. It sure helps me to feel the thump of the blade. Heed what Mark said. I carry a fillet glove, covered with a cotton canvas glove to wrap the line on, to break it off. I assume you are asking about using it on spinning reels. When you say "spincast" I picture a Zebco 33 or a Snoopy rod/reel. Also, what does a tackle shop installing the line have to do with its floating capabilities?

[Smj]

Sir...I've had 17# Fire Line on a 6'6" MH bassin' stick for quite a few years now. I'm tossing spinner baits and crankbaits mostly. I think the best thing about it for me, is when I hang the 5#er in heavy cover! just put the hammer down on 'em and pull 'em out!

As far as tossing size 4 & 5 spinners, I just don't think your going to get the distance that you would with 10# mono.

Smj

[FishSniffer]

From a Braid Newbie,

I just put PowerPro 20# on my spinning reel in place of Ultragreen #12 and these are my initial impressions.

Keep a large safety (diaper) pin, stainless if you can get it, on the outside of your jacket (you'll need it often) to attempt to take out the knots in the braid when you get them. Otherwise be prepared to strip it off.

Get a pair of Fiskars for kids with the rubber grips. (on sale at Wally's World a few days ago). Nail trimmers don't work as well and leave a frayed look instead of a clean clip.

Be careful when tying knots. Braid cuts through wet skin very easily! Use of the nitrile gloves greatly reduces this. Valuable when long-lining a fish onto the beach or guiding to the net.

Be prepared to not feel that stretch when the fish hits. I lost 3 of 4 metalheads yesterday becuase it wasn't there and short mono leaders don't strech that much. This will change your catch rate initially and take some getting used to.

Get some floatant and apply it to the last 20' or so to keep it on the surface after your initial cast. Surprisingly enough, with that on, you can keep it off the water surface with little effort when using a bobber.

It's a whole different feel. Yesterday was my first day using it and I'll keep it on at least a month. Good luck.

[ORpoke]

That is exactly why I first changed to Fireline...to better feel the larger spinners. Now I use the Fireline for everything for steelhead - bobbers, side drifting, spoons w/the baitcaster. I use 14# Fireline with about 10' of 12# ultragreen on the end via the 4X surgeons knot.

[Mr. Shannon O'Brien]

Yes it is a spinning reel that I use to toss blades at short distances. I'm looking at applying this stuff to use in creeks and small rivers the size of the North Santiam around Packsaddle.

I saw a guy that used it on a spinning reel and the line sunk into the spool and he was done. That is why I was wondering if a tackle store would be an ideal place to have to the put on really tight to prevent the line burrying.

Thanks for taking the moment to reply.

[salmurai]

I use Fireline on both a stradic 2000 and a 4000 and have not had any "digging in the spool" problems. I put the line on myself using a cotton glove and just weave the line through my fingers to get enough tension. Good Luck....